5 Simple Techniques For cci 500
5 Simple Techniques For cci 500
Blog Article
Aber der Akt stellt die letzte Eskalationsstufe vor dem gezielten Schuss dar, vergleichbar mit einem „Messer an die Kehle“ halten; die Kritik an dieser Äußerung kann ich daher überhaupt nicht nachvollziehen
„bei vielen von dir angesprochenen Fehlern gebe ich dir recht, angesichts der Länge des Podcasts halte ich die Liste aber nicht fileür derart gravierend, dass der ganze Podcast dadurch wesentlich leidet, ausser natürlich in den Augen derer, die wie Du so tief im Thema stecken, dass es zu einem bedeutenden Lebensinhalt geworden ist.
Das tun wir aber nicht, weil das Land sozusagen in eine Spannungssituation verwickelt ist. Und wofür ich plädiere, ist was ganz Einfaches: dass wir uns an die geltenden Gesetze und Richtlinien halten. Und die Welt um uns herum ist eben unsicherer geworden.
308stillbrass said: Understand that primer cup hardness isn't the only probable problem. If there is too much slop round the firing pin within the bolt encounter you may extremely conveniently get primer cratering That may be a Untrue optimistic for strain signs.
This is certainly an older thread, you might not get a response, and could be reviving an old thread. Remember to take into account making a new thread.
Shane Lindsey stated: Have employed both equally in 308 sized circumstances in bolt guns. Have not found A great deal of the change in them. Labored up the load with a single and after that modified them out. Not adequate change in precision to remember needing to vary. Click on to expand...
I'm shopping for some to test. I've acquired a perfectly constructed 243AI that I'll utilize them on too. I'll attempt them in my 30 Nosler but I'm igniting 80 grains of H1000. I'm making use of Gold match bench mag primers in it now but a unique primer could assist tighten groups up.
I have utilized BR-two's in 7mm rem mags with excellent final results, even in chilly temps. But, which was with pretty better circumstance fill of H1000 and Reloder 26, and Truthfully I choose to use mag primers, they may have not been harmful to obtaining consistent velocities, so it requires absent any fret of having ignition challenges with zero overall performance penalties.
Your CCI 200s are fully fine for your personal Garand. Just Make certain that you always seat your primers under flush. I exploit CCI 34s, but I would not hesitate to get a second to implement CCI 200s.
Ah Certainly, the internet marketing electric power of CCI. When you think all they have to state about an item they cost a lot more to suit your needs turn into the idiot and they just get richer. A minimum of, looking at their post they clarify that their mil spec primers usually are not the only real Think about protecting against slam fires.
„Und mal ganz ehrlich, angesichts der ganzen Hysterie damals sind wir Waffenbesitzer noch mal mit einem blauen Auge davongekommen, auch wenn es wehtut und ungerecht ist.“
I last but not least bought close to to loading some Forged bullets to test in a very 375 H&H. I was loading some Nosler Partitions simultaneously so I utilised CCI 250 primers in each of the conditions. I https://zundhutcheneurope.com used to be serious very careful not to mix the powders up and only experienced a person powder can open up at any given time but failed to Believe to A great deal with regards to the primers. I usually Check out around what I load and that is when I recognized the majority of the publications detailed CCI 200 primers with the Solid bullets.
When in essense all you have is an improperly supported primer with pressure towards it on just one side and no steel supporting it on the back side.
When in essense all you have got can be an improperly supported primer with strain versus it on 1 facet and no steel supporting it around the again side.